Moving from StayFi? The access point StayFi supplied is a UniFi device, so you can keep using it with BetterSTR. This guide walks you through resetting the access point, pointing it at the BetterSTR cloud controller with the BetterSTR UniFi Setup Tool, and adopting it in your BetterSTR account. The same steps work for any UniFi access point you already own.
🧩 Requirements
Before you begin, make sure you have:
-
A UniFi access point (for example the one StayFi supplied)
-
A Mac or Windows computer connected to the same network as the access point
-
The BetterSTR UniFi Setup Tool (download links below)
-
The access point’s MAC address, printed on the label on the device
-
A paperclip or similar tool for pressing the reset button
-
A UniFi WiFi subscription in BetterSTR: US$5 a month for the controller plus US$2 a month per access point (WiFi is included on BetterSTR Simple). You’ll need at least $5.00 in your account balance to subscribe.
🔄 Step 1: Factory Reset Your UniFi Device
An access point that was set up by StayFi (or any other controller) is locked to that controller, so you must reset it to factory defaults first. The setup tool only finds access points that are in their factory state.
-
Power on the device — Ensure your UniFi device is plugged in and powered on.
-
Locate the reset button — Usually a small recessed button on the back or bottom of the device.
-
Press and hold — Using a paperclip, press and hold the reset button for 10 seconds.
-
Wait for reboot — The device will reboot and return to factory default settings (this takes 1–2 minutes).
💡 Tip: The LED will flash during the reset process. Wait until it stops flashing and remains steady before continuing.
💳 Step 2: Turn On UniFi WiFi in BetterSTR
-
Log in to BetterSTR and open Devices → Wifi Devices in the left menu.
-
Under Full captive portal, click the UniFi Controller card. (Not “Customer-Owned UniFi”, which is for hosts who run their own UniFi controller.)

-
Check the fees and click Subscribe Now. You’re charged $5.00 to start the service, and each access point is added at $2.00 a month when you adopt it. If you’re on BetterSTR Simple the card says Included in BetterSTR Simple and takes you straight to the UniFi page instead.

-
On the UniFi controller page, click Connect to UniFi Controller. This creates your own site on the BetterSTR cloud controller, ready for your access points.
💾 Step 3: Download the BetterSTR UniFi Setup Tool
For macOS
-
Download: BetterSTR-UniFi-Setup-v1.0.5-mac.zip
-
Extract the ZIP file
-
The first time, Control-click (or right-click) the app and choose “Open”, then confirm. If macOS still won’t open it, go to System Settings → Privacy & Security and click Open Anyway.
For Windows
-
Download: BetterSTR-UniFi-Setup-v1.0.5-win.zip
-
Extract the ZIP file
-
Run
BetterSTR-UniFi-Setup.exe. If Windows shows “Windows protected your PC”, click More info and then Run anyway.
⚙️ Step 4: Run the Setup Tool
-
Open the BetterSTR UniFi Setup application
-
Select your network — The tool detects your computer’s network connections; choose the one your UniFi device is connected to
-
Click “🔍 Scan Network” — The tool scans your local network for UniFi devices that are still in their factory state (this takes 1–2 minutes)

💡 No devices found? Check the access point is powered on and on the same network as your computer. If it still doesn’t appear, it hasn’t been reset: repeat Step 1.
🌐 Step 5: Point Your Device at BetterSTR
Once the scan is complete:
-
Locate your device — Each device found is listed with:
-
IP Address
-
Model (e.g., UAP-AC-Pro-Gen2)
-
Status: Ready to configure
-
-
Double-click the device and click Yes to confirm. This tells it to connect to the BetterSTR cloud controller.
-
Wait for confirmation — You’ll see the message:
“Device at [IP address] has been configured! The device will now connect to your BetterSTR cloud controller. You can adopt it from the BetterSTR WiFi management page.”
-
Check the log — Verify that you see:
“✓ Successfully configured device at [IP address]”
🖥️ Step 6: Adopt the Device in BetterSTR
Give the access point a minute or two to check in with the controller, then:
-
Go to Devices → Wifi Devices and choose UniFi under Sections
-
Click Adopt Device (on the Access Points card), Adopt device at the top of the page, or Adopt an access point under Actions
-
Enter the MAC address from the device label (1). Colons or dashes are both fine.
-
Click Adopt Device (2). You’ll see “Device adoption initiated!”, and adoption finishes on its own within 1–2 minutes. This adds the access point to your WiFi subscription ($2.00 a month, pro-rated).

💡 “No unadopted device found with MAC address”? The access point hasn’t reached the controller yet. Check it’s online, wait a couple of minutes and try again. If it still isn’t found, run the setup tool again (Step 5).
🏠 Step 7: Assign It to Your Property
-
In the Access Points list, click the orange Not Assigned label next to the new access point, or its cog (Settings) button
-
Give it a name and choose the property under Assign to Property, so guests see that property’s WiFi form and guidebook
-
Click Save Settings

The same window lets you override the guest form for this property and set the guest speed. To change your network names and passwords, click Edit on a network in the WiFi Networks card. The guest sign-in form itself is set up on the WiFi settings page.
✅ You’re all set!
Your UniFi device is now connected to the BetterSTR cloud controller and ready for guests.